Yosemite Home Decor TAYSOM-BBN Manuale delle Istruzioni Scaricare il pdf (Pagina 1)

Installing the fan

All electrical work should only be undertaken after disconnection of the power by

removing fuses or turning off the circuit breaker to ensure all pole isolation of the

electrical supply.

Picture A

The following steps will guide you to a successful installation:

1. installation

2. assembly

3. Remote control and Wiring instruction

4. Attaching the blades

5. Installing light bulb and glass

1. installation

The should be screwed on to

a firm flat surface. The fixing location must

be able to withstand ten times the static

weight of the fan. If you have any doubts as

to the ability of your intended fixing location

to be able to withstand this loading. Please

contact our service help-line or another

competent authority to advise you. In most

situation two wood screws screwed into a

wooden joist is more than adequate to

support your ceiling fan.

The should

be screwed onto

the joist with the two wood screws provided.

The washers provided should go in the

followin

uence:

Screw head > round washer > spring washer > > Ceiling. Screw the

to the ceiling and make sure all connections are secure to prevent the

fan from falling. Fixings must screw into a joist and not just the plasterboard.

Mounting plate

mounting plate

Mounting plate

Fan

Round

Parts names and their relative positions

2.Fan assembly

Lift the fan up to the mouting plate and put the fan onto

the hook with one of the screw hole on canopy.

WIRING INSTRUCTIONS : Before doing wiring, ensure that you have all pole

disconnection of the electricity supply.

TRANSMITTER

RECEIVER OF

1 2 3 4

~ ~ ~ ~

DIP

DIP SWITCH

RECEIVER

ANTENNA

DIP SWITCH

DIP

~~~~

4321

DIP

~~~~

3. Remote control and Wiring instructions

Your fan is supplied with a radio frequency remote control unit, and the fan does not

have a pull switch for speed control, the fan can only be controlled by remote control.

You can find the unit in the box. Before connecting the wiring, please set up the code

of remote control.

CODE SWITCH: Codes are set by pushing dip switches up or down. It is imperative

that the code used for both transmitter and receiver is exactly the same, otherwise the

remote control will not work. Please note the code switch will enable you to operate a

second remote controller independently.

For example, if you have two ceiling fans with

2 remote control units, set 2 different codes for each set of transmitter/receivers. This

means you can operate each ceiling fan independently. Please see following drawing.

Put the receiver of remote control

through hanger bracket (as picture).

Connect the A.C. power supply wire that

come from the ceiling to the Black and

White wire of receiver which is mark

with label “L” & “N”. In most cases,

Black wire is LIVE is connected to “L”

Black wire, White wire is NEUTRAL is

connected to “N” White wire.

Connect the 3 lead wires coming from

the fan housing with 3 wires coming

from the other side of the remote control

receiver where indicated sticker with

brown, blue, orange block.

Black TO Black (Live wire of fan) White TO White (Neutral wire of fan)

Blue TO Blue (Live wire of light)

PORTANT : THIS APPLIANCE MUST BE EARTHED.

4. Attach the assembled blades

Carefully unwrap the blade and put

the blade into the hole of sideband.

Align the blade with the holes on the

blade carrier which is pre-assembly

onto the motor. Use the screws and

fibred washers provided to connect

them.

The rubber round washer and metal

round washer should go on top the

blade between the head of the screw

and the surface of the blade. Ensure

the screws are tightened up firmly.

Repeat this process for all blades.

Completely remove one of the three

provided screws on the small round

plate under the motor, and loosen

partially the other two screws (remain a

half part in the round plate).

To fasten the Light Fitting onto the small

round plate, align the two keyhole slots

on the light fitting to the partially

loosened screws and turn the light

fitting in place so that the fitting is held

temporarily.

5. install light fitting and bulb & shade

Your fan is supplied with 60W light bulb.

You must not touch new bulb with bare

fingers when you take the bulb from

box. The body oil residue may cause the

bulb to explode. Use tissue or cloth to

protect the new bulb from your fingers.

Before install the bulb, make sure the

power is disconnected. Put the E12 X 2

40W Max. to the socket in the fitter.

Replace the completely removed screw to the small round plate, then tightly fasten

the 4 screws to hold the li

ht fittin

securel

fter finishing the following step for

installing light bulb and make sure

light is worked properly, please lift the

canopy and carefully up to

mounting

plate

, carefully put all wires into the

canopy and don’t bent or broken the

wire. Use the canopy set screw to

screw it firmly.

Put the shade into the light fitter and

twist it tight. Ensure the shade is

tightening firmly, the shade will drop

off and broken not installed properly.

Now, your fan installation is complete.

Now is a good time to test that the fan operates correctly. Turn on the power

and use the transmitter to Control your fan, checking the fan speeds and light

kit\ are worked properly. Please see page 10 for remote control function

details.

2 1

ML-08-03

2.Fan assembly 1

Sommario

Pagina 1 - 2.Fan assembly

Installing the fan All electrical work should only be undertaken after disconnection of the power by removing fuses or turning off

Commenti su questo manuale

Nessun commento

Yosemite Home Decor TAYSOM-BBN Manuale delle Istruzioni Pagina 1

Navigare online o scaricare Manuale delle Istruzioni per Accessori per il raffreddamento hardware Yosemite Home Decor TAYSOM-BBN. Yosemite Home Decor TAYSOM-BBN Instructions / Assembly Manuale Utente

Sommario

Commenti su questo manuale